Search the Community

I have the navionics card and a gps antenna installed on my Medallion viper 2 module. The GPS and card work fine. However, the boat doesn't stay centered on the map so I have to keep scrolling the map when we move around a lake. I can't find anything in any of the menus on the screen but is there any option where the system automatically scrolls the map based on where the boat is? Like a cross hair button?

Looking for some help - putting myself out there, so please take it easy on me.... Hv a '21 MXZ23 and would like to load "The Book" DVD (Wakeboard Instruction) to my boats hard drive. Here is what the Owners Manual states - (I just DO NOT understand this language) PDF / Video Viewer: The PDF and VIDEO buttons will allow the driver to view PDF's and play videos that have been stored in the sytem, or that are on a USB stick that is inserted into the dash USB port. These buttons will be selectable only when the engine is OFF, or if the engine is in idle. The Viper 111 system supports the following media formats for video playback: Video .divx/.cv/.flv/.h263/.h254/intel-h263/.jpeg/.mpeg/.mempeg/.msvideocoder/.wmv/.xvid or Image .fig/.jpeg/.png/.tiff File Transfer: Move files from USB input devices to the system by highlighting the file to be copied, than selecting COPY. Please allow for sufficient amount of time for the file to transfer. The Viper 111 system supports the following media formats for file transfer: audio.mp3, video.mp4/.avi/.flv/.jpeg/.mpv/.png/.wmv, and image.pdf. I don't even know where to start w this. Is there anyone out there on this forum that understands this language and can lay it out for me? How do I get my DVD's onto the boats hard drive? Thank you in advance for any assistance you can provide.

I have a 2010 Wakesetter 247 LSV. I have been reading here and trying to fix a problem with the power wedge. Power wedge stopped working. I was getting wedge down alarm even though it was all the way up. Couldn't calibrate as it wouldn't move in or out of the water. I have checked and run actuators manually and they work. They are 5 lobe, were replaced by the dealer a year ago. Lenco control box is original 3 lobe, but was working. The position sensor always read 66 on calibration screen regardless of position when I ran the actuators manually(I wired in a bypass switch). Thinking this might be the problem I replaced the position sensor. Still no luck getting anything to work correctly. I reset the Maliview viper to factory settings to see if that would help. It didn't. At this point I found the fuse everyone had mentioned in the harness clip under the dash that I overlooked. It was a 15amp fuse and it was blown. I replaced it and hooked everything back up like it was originally thinking I had found the problem. Here is now the issue. Sitting on the trailer in my driveway when I turn the key on the wedge starts moving up on it's own regardless of starting position. If I press the down MUX button it will go down but as soon as I release the button it starts going back up and the actuators continue to run when its get all the way to the top. Any ideas what might causing this? Also I have tried calibrating the sensor since replacing the fuse but I can't get down number below 166 regardless of how I adjust the sensor. I get readings of 166 down and around 488 in the up position. I keep battery charger hooked up the whole time so my voltage readings at gauges in dash are around 13-13.5V Any ideas whats causing the wedge to move up on it's own? Or ways to bring sensor calibration down? It will be appreciated.

I have a 2010 Wakesetter 247 LSV. In trying to fix a problem with the power wedge, I reset the Maliview viper to factory settings. Now the radio won't respond to any button presses in the MUX switch. It was working fine before reset. I checked the MUX and the buttons work for other functions. Strange thing is that if I plug iPhone into cable in glovebox media port it will play music through stereo at about half volume but still no control through Mux or viper screen in the Maliview. Any help or ideas will be appreciated.